Adding a User for Incoming IPv6 FTP REXEC Logons

To add a new user for incoming FTP/REXEC logons, press the F6 key from the Work with FTP/REXEC Logon Security IPv6 screen (STRAUD > 11 > 2), as shown in Setting Additional Controls for Incoming IPv6 FTP REXEC Logons.

The Add FTP/REXEC Logon User IPv6 screen appears:

​                         ​ Add FTP/REXEC Logon User IPv6​                                                                                                           ​ Type information, press Enter.                                                ​    ​ User  . . .​ ​                   ​   ​ Name, generic*, User Group, *ANONYMOUS, F4 ​                                                   ​ 1=Allow​                                                                    ​ Prfx​ 2=Reject​                     ​ IPv6 Address​                                 ​ Lngh​ 3=Altlogon​   ​ Text​           ​                                               ​    ​  ​  ​  ​                      ​  ​                                               ​    ​  ​  ​  ​                      ​  ​                                               ​    ​  ​  ​  ​                      ​  ​                                               ​    ​  ​  ​  ​                      ​  ​                                               ​    ​  ​  ​  ​                      ​  ​                                               ​    ​  ​  ​  ​                      ​                                                                    ​      More...​                                                                                   ​ For *ALTLOGON (alternative logon):​                                                ​ Validation password . .​ ​                   ​ ​ Password, *NOCHK, *SYS, *PGM  ​     ​ Alt User  . . . . . . .​ ​           ​         ​ Name, *SAME, F4 for list      ​     ​ Alt Password  . . . . .​ ​           ​         ​ Password, *SAME, *BYPASS, *PGM​     ​ Alt Current library . .​ ​           ​         ​ Library, *USRPRF              ​                                                                                    ​ F3=Exit​  ​ F4=Prompt​  ​ F10=Additional parameters​  ​ F11=Alt.view​  ​ F12=Cancel ​    ​                                                                                                                                                                  ​

Enter the name of the new user or group in the User field. This can be a specific or generic* name. Use the value *ANONYMOUS for anonymous connections. For a list of possible values, press the F4 key.

The body of the screen is made up of lines that can refer to different IPv6 address ranges. Possible values include:

IPv6 Address

The IPv6 address for the range of addresses. In addition to an IPv6 address, you can set this field to *ALL for rules applied to all IPv6 ranges that aren't otherwise specified.

Address prefix length

The length of the IPv6 address prefix. This can be set to from 1-128.

1=Allow 2=Reject 3=Altlogon

How Firewall responds to requests by the user for incoming FTP/REXEC logons from this IPv6 range. Possible values include:

• 1: Accept logon requests
• 2: Reject logon requests
• 3: Require an ALTLOGON connection to connect, as set on the Modify FTP/REXEC Logon User screen, shown at Modifying a User for Outgoing IPv6 FTP Connections.

Text

A free-form text description of the rule.

If you are using *ALTLOGON, as indicated in IBM documentation, the user takes on a different identity, including that user's authority settings. Set the section of the screen labeled For*ALTLOGON (alternative logon):​ to appropriate values.

After entering information in these fields, press the Enter key.